Non-destructive entry first, always - and we re-key Schlage, Kwikset, and Baldwin locks on the spot while you watch
You get a price before we start. It does not change when we arrive. No surprises.
Schlage Lock Installation & Rekey in Long Beach: What to Know First
We provide independent Schlage lock installation and rekey services across Long Beach, from Belmont Shore to Bixby Knolls and the neighborhoods near Cal State. Most residential Schlage rekeys are completed in under an hour; installations typically run 90 minutes when we’re replacing a like-for-like deadbolt or lever set. Every job starts with a written price quoted on the phone, and under Haven Standard Clause 1, that price is contractually the same number on the invoice.
This page is for Schlage owners in Long Beach who need a lock installed, rekeyed, or diagnosed, whether it’s a standard B60 deadbolt, a keypad BE365, or a smart Encode Plus. Call (424) 340-6795 for a written estimate with no dispatch fee.
How Schlage Products Fail - and How We Fix Them
- BE365 keypad deadbolt: ghost entry codes after salt-air exposure. The membrane beneath the keypad degrades faster in Long Beach than inland because marine moisture creeps past the seal. We see this in ocean-adjacent homes near Bluff Park and the Peninsula. The fix is a full keypad module replacement, not a battery swap. We stock OEM modules and can rekey the cylinder to your existing key during the same visit.
- Encode Plus smart lock: Bluetooth hub dropout in stucco-and-wire-mesh construction. The 2.4 GHz signal gets eaten by the wire lath common in 1950s Long Beach tract homes, especially in Lakewood Village and California Heights. Customers think the lock is defective; usually it’s a placement issue. We test signal strength at the door before we install, then recommend a Wi-Fi bridge position that actually holds.
- B60 deadbolt: tailpiece shear after improper rekey by a hardware store. The B60 uses a stamped steel tailpiece that cracks if the cylinder is removed without supporting the bolt mechanism. We replace with a hardened steel aftermarket tailpiece where the customer wants added durability, or OEM if they prefer factory spec. Either way, we document the part number on the invoice.
- FE595 lever lock: clutch slip from over-torqued installation. This entry lever with keypad is sensitive to backset alignment. When the bore hole is drilled off-center, which we find in DIY installations around Naples and the Marina, the clutch mechanism strips within six months. We rebore or use an adjustable backset adapter, then set the clutch preload with a torque gauge.
- AL series commercial levers: cylinder rotation from worn cams in high-traffic Port buildings. The AL53PD and AL80 are common on Long Beach commercial doors, but the zinc alloy cams fatigue faster than the brass ones in Schlage’s ND series. We upgrade to ND-spec cams where the door sees 200+ cycles daily, or rekey and replace the cam if the customer wants to keep the existing hardware.
Our Schlage Lock Installation & Rekey Process
- 1
Call and scope. You describe the lock, the symptom, and the door type. We quote a firm price for the work, with part numbers named where relevant. Haven Standard Clause 1 applies: the price on the phone is the price on the invoice.
- 2
Dispatch with parts. Our technician arrives with Schlage-compatible cylinders, tailpieces, and keypad modules pre-loaded, based on what you described. Background-checked, uniformed, with a photo ID badge.
- 3
On-site diagnosis. We open the lock, name what we find, and confirm the price before touching tools. If the scope changes, we stop and re-quote in writing. No surprises.
- 4
Repair or install. For rekeys, we pin the cylinder to your new key code and test all cuts. For installations, we set backset, bore alignment, and strike depth, then cycle the lock 50 times minimum.
- 5
Documentation and cleanup. You receive a written invoice with part numbers, a photo record of the completed work, and the 365-Day Done Right Promise card. We sweep the work area before we leave.
What Schlage Lock Installation & Rekey Costs in Long Beach
| Service | Typical Range | What Affects Price |
|---|---|---|
| Residential deadbolt rekey (B60, B562) | $35-$55 per cylinder | High-security sidebar, key control registration |
| Keypad lock rekey (BE365, FE595) | $55-$85 per cylinder | Keypad module condition, membrane replacement |
| Smart lock installation (Encode, Encode Plus) | $180-$320 | Door prep condition, Wi-Fi bridge placement, app setup |
| Commercial lever rekey (AL/ND series) | $45-$75 per cylinder | Cam replacement, master key system integration |
| Full deadbolt replacement with new Schlage hardware | $140-$260 | Grade 1 vs. Grade 2, finish matching, strike reinforcement |
These are the ranges we quote on the phone, and they are the ranges on the invoice. No call-out surcharge is added when we arrive. The only variable is what we find when we open the door, and if that changes the scope, we stop and re-quote before proceeding.
Call (424) 340-6795 for a free estimate. We will name a number you can write down.
Why Long Beach Homeowners Call Novak Lock & Security Long Beach for Schlage Work
We are not a dispatch mill. Daniel Novak grew up in Culver City, trained at Los Angeles Trade-Technical College, and has been installing and rekeying locks since 2002. When a Schlage Encode Plus fails to pair in a Signal Hill home with aluminum wiring, or a B60 tailpiece shears in a Belmont Heights rental, we have seen it before and we bring the part that fixes it.
The 365-Day Done Right Promise covers every installation and rekey. Our technicians are background-checked, uniformed, and work to The Haven Standard, the same documentation framework applied across all ten Haven brands. We also service Kwikset and Medeco, so if your Schlage is part of a mixed-brand setup, we handle it without subcontracting.
The name on the van is the same name on the invoice. That is the whole argument.
FAQs
No. Rekeying the cylinder does not void Schlage’s limited lifetime mechanical warranty, provided the work is done without damaging the lock housing. As an independent Schlage service provider, we use factory-compatible pinning kits and document the work so warranty claims remain valid. If we install a new Schlage product, the original manufacturer warranty transfers to you unchanged. Call (424) 340-6795 if you need warranty documentation for a recent installation.
Most residential Schlage deadbolt rekeys are completed in 30 to 45 minutes on-site. We stock common Schlage keyways, including SC1 and SC4, so we do not need to order cylinders. Same-day appointments are usually available. Call (424) 340-6795 to check today’s schedule.
Repair makes sense when the lock body is sound and the failure is isolated to the cylinder, tailpiece, or keypad module. Replace when the bolt mechanism is worn, the door prep is damaged, or you are upgrading from a Grade 2 to a Grade 1 for insurance compliance. We will show you the wear and name the price for both options before you decide.
We stock both and tell you which we are using before we start. OEM Schlage cylinders and keypad modules carry the factory warranty and are necessary for warranty repairs. Quality aftermarket parts, such as hardened tailpieces, cost less and often outlast factory equivalents in high-cycle applications. The invoice lists the part number and origin either way.
Yes, if the smart lock has a traditional key override cylinder. The Schlage Encode Plus and BE365 both accept standard SC1 or SC4 cylinders that we can pin to your existing key code. Pure electronic locks without a mechanical keyway cannot be rekeyed in this way. We will verify your model and keyway before we dispatch.
Written by Daniel Novak, Owner, Novak Lock & Security Long Beach at Novak Lock & Security Long Beach, serving Long Beach and nearby areas.